The material of the milk white endurance board is light and easy to handle: it weighs only half of the glass, saving time and effort in handling and installation, and making construction management convenient and easy. Weathering resistance and excellent lighting: It can withstand long-term ultraviolet radiation, with excellent lighting effects and can save a lot of energy consumption. Ningbo Chaomei Plastic is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. It strictly implements the ISO9001 quality system and ROHS instructions. Below, the editor will share with you the optical performance of endurance boards? 1. Transmittance: The transmittance of PC endurance board is over 85%, which is equivalent to glass. 2. Weathering resistance: Generally, PC endurance boards are prone to yellowing and surface degradation when exposed to ultraviolet radiation for a long time outdoors. The surface of the ultra beautiful PC endurance board is attached with a layer of anti UV layer, and even after long-term outdoor exposure, its optical and mechanical properties do not show significant changes.

Green endurance board is lightweight and easy to handle: it weighs only half of the glass, saving time and effort in handling and installation, and making construction management convenient and easy. Weathering resistance and excellent lighting: It can withstand long-term ultraviolet radiation, with excellent lighting effects and can save a lot of energy consumption. Ningbo Chaomei Plastic is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. Thermal performance of endurance boards: 1. Melting temperature: The melting temperature of PC endurance board is 135 ℃, and its continuous use temperature reaches 120 ℃. 2. Linear expansion coefficient: The linear expansion coefficient is 7 × 10-5cm/cm/℃ is relatively small in plastic. 3. Embrittlement temperatu

The red endurance board is made of high-performance engineering plastic polycarbonate or polycarbonate acid resin. Its characteristics include impact resistance, unbreakability, strength hundreds of times higher than that of reinforced glass and acrylic board, toughness, safety, anti-theft, and bulletproof effects. Can be arched and bent: with good workability and strong plasticity, it can be bent into arched or semi circular shapes according to the actual needs of the construction site. Ningbo Chaomei Plastic is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. Mechanical properties of endurance boards: 1. Impact strength: PC endurance board has excellent impact resistance, with an impact resistance 250 times that of glass of the same thickness and 30 times that of acrylic board. The impact strength of Pc endurance board is called "transparent steel plate". 2. Good tensile strength, PC endurance board has good heat resistance, and even at 120 ℃, its tensile strength can still reach 350kgf/cm2. 3. Bending strength: PC endurance board has good bending resistance, and even if the bending angle reaches 90 °, it still does not break.

Transparent endurance boards are suitable for bizarre decorations in gardens, amusement venues, and corridors and pavilions in rest areas; Suitable for interior and exterior decoration of commercial buildings and curtain walls of modern urban buildings; Suitable for transparent aviation containers, motorcycle windshields, aircraft, trains, ships, cars, boats, submarines, and glass military police shields; Suitable for the layout of telephone booths, advertising signs, lightbox advertisements, and display exhibitions; Suitable for instruments, meters, high and low voltage switchgear panels, and military industries; Suitable for high-end interior decoration materials such as walls, roofs, screens, etc; Suitable for sound insulation barriers on highways and urban elevated roads; Suitable for agricultural greenhouses and breeding greenhouses; Suitable for the ceiling of modern ecological restaurants; Suitable for bicycle sheds, balcony sunshades, and rooftop rest booths in all units or communities; Suitable for lighting ceilings in office buildings, department stores, hotels, villas, schools, hospitals, sports venues, entertainment centers, and public facilities. Ning

The brown PC endurance board is made of high-performance engineering plastic polycarbonate or polycarbonate acid resin. Its characteristics include impact resistance, unbreakability, and strength hundreds of times higher than that of reinforced glass and acrylic boards. It is tough, safe, anti-theft, and bulletproof with the best results. Can be arched and bent: with good workability and strong plasticity, it can be bent into arched or semi circular shapes according to the actual needs of the construction site. Ningbo Chaomei Plastic is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. Introduction to Endurance Board: Endurance board (also called polycarbonate solid board, bulletproof glass, PC solid board) is made of high-performance engineering plastics - polycarbonate (PC) resin. It has the characteristics of high transparency, light weight, impact resistance, sound insulation, heat insulation, flame resistance, aging resistance, etc. It is a high-tech, extremely excellent comprehensive performance, energy-saving and environment-friendly plastic board. It is currently widely used in the world as a plastic building material, There are advantages that other building decoration materials cannot match. The surface with UV can withstand aging for up to 15 years.

1. It is necessary to check whether the expansion reserve of the sunlight board is reasonable, whether the cutting size of the board is qualified, and whether the reserved expansion gap is even and sufficient. 2. When installing and fixing the solar panel and accessories, it is best to tear the protective film apart by 30mm to 50mm to avoid the accessory pressure strip from pressing the protective film. 3. If the solar panel has UV coating, it is important to distinguish between the UV resistant side facing outward and the side without UV coating facing inward during installation. Do not install it incorrectly. 4. If it is a hollow solar panel installation project, a minimum of 20mm space should be maintained at the edges of the panel connection, and the clamping accessories connected to each other in the solar panel installation project should have at least one rib missing. 5. After installing the accessories, tighten the connection screws of the sealing strip and plate evenly and do not use excessive force. If leakage occurs due to installation errors, timely use the sealing glue for treatment. 6. If it is necessary to drill and nail the board by oneself, it is necessary to consider the thermal expansion and contraction properties and principles of PC board, and leave reasonable gaps. 7. Check if there are any leaks after the board device is installed, and check all aspects that need to be noted, including app

The biggest feature of Pc solar panels is that they can be cold bent along the direction of the ribs into arches with different bending radii, which not only increases the lighting area but also meets the bending requirements of architectural art design. And it has improved the load-bearing capacity of the board, which is beyond the reach of ordinary glass. The correct direction allowed for bending of the sheet is to avoid cracking on the exposed side. Ningbo Chaomei Plastic Sheet Co., Ltd. is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. It strictly implements the ISO9001 quality system and ROHS instructions. What are the precautions for a sunboard? When installing, the construction organizer must understand the text instructions and precautions printed on the protective film clearly, and explain to the operator, especially paying attention to the standard of which side faces outward. Never install it by mistake. Sunshine board, also known as PC board, is a new type of decorative material commonly used internationally for its high strength, transparency, sound insulation, and energy efficiency. It has excellent perfor

Pc solar panel is a new type of high-strength, waterproof, transparent, and energy-saving roofing material, mainly made from PC raw materials. PC solar panels are produced and manufactured using polycarbonate as the main raw material. Sunshine board quickly entered the building decoration industry in the mid-1980s. What is the development prospect of solar panels? The application of solar panels has just begun, and it is currently under construction in modern agricultural greenhouses in China. Important in Beijing and some cities in the north. In terms of greenhouse construction, there are greenhouses built entirely using solar panels, greenhouses built with gable walls using solar panels, and greenhouses built with gable walls and side walls using solar panels. In terms of greenhouse efficiency, there are production oriented greenhouses, trade oriented greenhouses with flower trading centers as the main focus, and greenhouses with scientific research as the main focus. These greenhouses are partially or entirely covered with solar panels. Ningbo Chaomei Plastic Co., Ltd. is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. It strictly implements the ISO9001 quality system and ROHS instructions.

The application of PC solar panels has just begun, and it is currently under construction in modern agricultural greenhouses in China. Important in Beijing and some cities in the north. In terms of greenhouse construction, there are greenhouses built entirely using solar panels, greenhouses built with gable walls using solar panels, and greenhouses built with gable walls and side walls using solar panels. Ningbo Chaomei Plastic Company is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. It strictly implements the ISO9001 quality system and ROHS instructions. What are the uses of solar panels? Strange decorations in gardens, amusement venues, and corridors and pavilions in rest areas; The interior and exterior decoration of commercial buildings, and the curtain walls of modern urban buildings;

The existing tape on the sunlight board. It is only used for temporary protection of the edges of the board and is not resistant to aging. In installation engineering, the board must be cut according to size. After cutting, special engineering tape must be used to seal the hole grid at the end of the board according to the installation regulations, and the original tape must be replaced. Ningbo Chaomei Plastic is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate PC endurance sheets. It strictly implements the ISO9001 quality system and ROHS instructions. Storage and transportation of solar panels: (1) Store indoors and never allow direct sunlight or rain (2) Use your hands to stack and do not exceed a height of two meters. No heavy objects should be pressed on the board, and there should be no hard objects between the boards. (3) The storage room must be kept clean, dry, and avoid dust intrusion. Other chemical substances should not be stored indoors at the same time. (4) Do not damage or remove the protective film during storage. (5) During transportation, it must be placed flat on a clean flat pallet with an area larger than the board. If necessary, it should be properly tied to avoid vibration a

PC sunlight board is a new type of high-strength, waterproof, transparent, and energy-saving roofing material, mainly made from PC raw materials. PC solar panels are produced and manufactured using polycarbonate as the main raw material. Ningbo Chaomei Plastic is a plastic sheet production enterprise that integrates research and development, production, sales, material processing, warehousing, and distribution of high-quality polycarbonate (PC) sheets. It strictly implements the ISO9001 quality system and ROHS instructions. Sealing technology for solar panels: The existing tape on the solar panel. It is only used for temporary protection of the edges of the board and is not resistant to aging. In installation engineering, the board must be cut according to size. After cutting, special engineering tape must be used to seal the hole grid at the end of the board according to the installation regulations, and the original tape must be replaced. The special adhesive tape for installation engineering should have good weather resistance, and be used for a long time without losing its adhesion and mechanical strength, What are the points to pay attention to when applying adhesive tape during the installation operation of the solar panel?

Apply professional measuring instruments such as micrometers and meters to accurately measure PC endurance boards. First, calibrate the caliper or meter gauge to the "0" position. Prepare to test the PC endurance board and remove the protective film from the upper edge of the board. Accurately measure the caliper, insert it horizontally into the PC board, gently press the caliper button, and observe the data on the record sheet caliper. Remember the above process and follow this method to remove two to three points on each of the four sides of the PC board. In total, at least 8 to 12 points must be accurately measured and recorded. The average of the obtained data from each point is the relative accurate thickness of the PC board, and then refer to the customized thickness of the furniture board for comparison. Calculate the thickness of the PC board by accurately measurin

Experts from PC diffusion board manufacturers believe that users need to pay attention to some important matters when installing the board. Firstly, the board should be cut according to the actual size required, and special adhesive tape with strong adhesion should be used to seal the holes on the board, so that the fixed board is not prone to loosening. PC diffusion board company suggests that users should be careful when applying adhesive tape, not to dirty the surface of the board, and not to let the tape come into contact with dust or water. They should also ensure that the tape completely covers the hole, and the tape is harmless and will not affect the quality of the board. Before installing the board, the user also needs to carefully check whether the tape is intact and undamaged. If there are any loose tapes, the user should replace them. Users should regularly maintain and maintain the board during its use, extend its lifespan, and save costs. PC diffusion board manufacturers believe that users can use water with moderate temperature and low corrosive detergent to clean the board. They can use a soft cloth to slowly wipe the board, and cannot use rough, hard, or sharp tools to wipe the board. Users should wipe the board dry and not leave it in a wet state. Alcohol can help users remove oil stains, glue and other marks on

The cloth canopy cannot withstand strong winds; Glass is a brittle material that is prone to breakage; A sturdy stainless steel canopy has the problem of high noise during rain. With the birth and use of PC board, the emergence and prevalence of PC endurance board canopies have greatly helped us solve the problems of wind resistance and noise. The PC endurance board canopy is composed of a special engineering plastic bracket and PC endurance board panels (also known as sunlight board panels), which have strong continuous combination. And the PC endurance board canopy has an elegant and elegant appearance, a sturdy and durable structure, and a service life of 8-15 times that of a regular canopy. Even in harsh weather conditions, the outdoor endurance board canopy can have a service life of more than 10 years. And the PC endurance board canopy can independently filter UV radiation and withstand the frontal attack of a Category 12 typhoon. Excellent performance of PC endurance board canopy: one side of the board has anti condensation treatment to prevent condensation water from falling; The board has a UV resistant layer on both sides, providing better weather resistance. Features: Wind resistance, impact resistance, corrosion resistance, rainwat

If there are stains on the PC endurance board, it is necessary to clean it in a timely manner. If you want to clean the endurance board, you must do the following: 1. Rinse with warm water below 60 ℃. 2. When cleaning, neutral detergents should be used. If corrosive detergents are not used, it may cause damage to the endurance board. 3. During the cleaning process, gently wipe with a soft cloth or sponge dipped in neutral solution. If hard and sharp tools such as rough cloth, brushes, and mops are used for cleaning, it can cause significant damage to the endurance board. 4. When there is grease, wet paint, tape marks, etc. on the surface, a soft cloth can be used to wipe with alcohol. 5. Rinse the cleaned dirt thoroughly with clean water.

Is the thicker the Pc board, the more durable it becomes? Is the thicker the endurance board, the better? I want to build a breeding shed. What is the best thickness to choose? Today, I will talk to you about the advantages and disadvantages of PC endurance board thickness. Endurance boards have high light transmittance, up to 88%, and are as transparent as glass. In modern society, there are more and more places where endurance boards are used, such as breeding sheds, light boxes, sound barriers, etc. However, what thickness of endurance boards is needed to be considered appropriate? Advantages of endurance board: It has high transparency, impact resistance, and is unbreakable; If the endurance board is maintained steadily, the service life can be more than ten years, and the endurance board ceiling is also the same. But there is one drawback, which is that the cost is relatively expensive. The thicker the endurance board, the higher

There are many colors for PC solar panels and PC endurance panels, among which the more common ones are sky blue, transparent, grass green, milky white, and brown. However, customers who apply them more often find that different manufacturers produce PC solar panels and PC endurance panels of the same color series with significant deviations, such as milky white. Some manufacturers produce boards that are softer and milky white, Some manufacturers produce boards that are darker or have some other colors. Many manufacturers also have significant differences in the same color of PC solar panels and PC endurance panels. What is the reason for this? Manufacturers that use a large number of imported raw materials. Among them, the larger color deviation is still caused by small manufacturers. Due to the limited use of new and upgraded materials in the boards produced by these manufacturers, most of the purchased materials are sold in the market from other recycled material manufacturers, and excessive mixing of raw material distributors results in an increasing color deviation of the boards. Moreover, this type of manufacturer does not have their own raw material secret recipe, which is also a key reason for color deviation.

What are the reasons for the blistering of PC endurance boards? How should we avoid it? There are usually two reasons that cause blistering on the board: if the PC endurance board is heated for too long/at too high a temperature, the board will blister (if the temperature is too high, the inside will start to melt, and external gas will enter the inside of the board). However, unlike in sheet metal production where the temperature and heating time are controlled by equipment during later processing, it can only be determined manually, so bending generally requires experienced professional workers to complete. PC polycarbonate sheets themselves absorb moisture (at standard atmospheric pressure, 23 ℃, a water absorption rate of 0.15% with a relative humidity of 50%). Therefore, if the finished endurance sheet is stored for a long time, it often absorbs moisture from the air. If the moisture is not removed before molding, bubbles and misty micropores will appear in the formed product, which will affect its appearance. To avoid abnormal situations caused by moisture, the board should be pre dried at a lower temperature for a period of time before heating and forming. Usually, the moisture can be removed at a temperature setting of 110 ℃~120 ℃, and the water removal temperature should not be higher than 130 ℃ to prevent the board from softening. The duration of removing moisture depends on the moisture content of the board, the thickness of the board, and the drying temperature taken.

Compared with hollow slabs, the installation steps of PC endurance slabs have a more severe impact on thermal expansion and contraction, mainly manifested in greater stress under the same temperature difference and greater production stress when changing the same shape. The greater the thickness, the more obvious the stress and difficult to eliminate. During the production process, endurance boards usually curl without waiting for the product to cool down safely. The pressure generated during this process cannot be underestimated. Please let it stand for 24 hours when unwinding. For ease of transportation, endurance boards are sold in coils of 30M or even 60M. Please use an electric saw during installation. The length of each board is generally around 6M. The longer the plate, the more difficult it is to properly control thermal expansion and contraction. When temporarily unwinding and sawing due to sale, please fix the left and right sides of the area where the board is to be sawn. Vibration can easily cause uneven cutting edges, and if the cutting edges are uneven, they will inevitably crack under stress. If you use a wallpaper knife to break the ring, please pay attention to the uneven edge when folding repeatedly, which can easily concentrate stress on nearby ar

The mechanical properties, electrical properties, flame retardancy, and UV resistance of the ultra beautiful PC frosted board are the same as those of the durable board. The difference is that the light penetrates the PC frosted board, which is softer and can diffuse light, making the light distribution more uniform. After the light penetrates, it brings out a warm and elegant atmosphere. Scope of application: Fantastic decoration, modern urban curtain walls, interior decoration, indoor partition screens, bathroom partitions, etc. PC frosted board features, weather resistance, and a UV resistant co extruded layer on the surface, which can prevent resin from yellowing due to fatigue caused by sunlight and UV rays. The surface co extruded layer has chemical bonds to absorb ultraviolet light and convert it into visible light, which has a good stabilizing effect on plant photosynthesis. Impact resistance: The impact strength of PC board is 250-300 times that of ordinary glass, 20-30 times that of acrylic board, and 2 times that of tempered glass, with almost no risk of fracture. Flame retar

Can PC endurance boards processed with PC boards replace tempered glass? PC endurance board is made of polycarbonate solid board, which is commonly used for lighting and glass because people find it economical. Will glass really be replaced by PC endurance boards? Let's take a look. Tempered glass is made by uniformly heating ordinary glass. When it approaches the softening point, it cools evenly at the corresponding cooling rate according to the thickness. There is a strong internal stress inside the glass, and the tensile stress in the inner layer and the compressive stress in the outer layer are in a stable stress equilibrium state. The ultra beautiful PC endurance board is made of high-performance engineering plastic polycarbonate or polycarbonate. 1. Flammability: The self ignition temperature of PC heat-resistant board is 630 (the flammability of the board reaches GB (8624-1997, B1 level), and it belongs to fire-resistant engineering materials. 2. Chemical corrosion resistance: PC resistant plates have outstanding chemical corrosion resistance, and can withstand corrosion from various organic acids, inorganic acids, weak acids, vegetable oils, neutral salt solutions, fatty hydrocarbons, and alcohol at room temperature. 3. Heat and cold resistance: PC endurance board has good temperature difference resistance and can adapt to various adverse weather cha

1. In order to simplify the installation of anti-static PC boards and provide greater flexibility for future device configuration changes and expansions. 2. The equipment in the computer room can be freely electrically connected through the anti-static floor, making it easy to lay and maintain, making the computer room clean and beautiful. 3. It can protect various cables, wires, data cables, and sockets from damage. 4. The computer room can use the underfloor space as a static pressure box for air conditioning to achieve satisfactory airflow organization. No matter where the computer equipment is installed, the air after the air conditioning can be obtained through the air outlet of the anti-static PC board. 5. It is beneficial for the repair and maintenance of the equipment bottom. 6.

1. Pc diffusion plates are inexpensive, convenient, and portable in lighting appliances. However, due to the interference of external natural light, the measured values are generally higher. This instrument is only suitable for reference comparison and cannot be used as an accurate instrument. 2. Transmission haze tester: The Pc frosted diffusion plate is less affected by external factors, so the test results are lower and more accurate than the illuminometer. Generally speaking, diffuser manufacturers use this instrument to test the transmission haze of their products. 3. Integration sphere: The integration sphere measures the transmittance of the diffusion plate very accurately and is almost unaffected by external environmental interference, so the data obtained from testing the same plate is lower than the above two. Due to the high cost of instruments, only la

The ultra beautiful PC endurance board series products have good surface gloss, good heat resistance, self extinguishing, excellent impact performance, small expansion coefficient, stable size, excellent electrical and chemical resistance, good fatigue strength, and comply with the EU ROHS directive and strict UL safety standards. UL94 has a fire resistance rating of V0, V2, and HB, and is widely used in electronic components, electrical enclosures, switch panels, junction boxes and charger enclosures, automotive instruments, and panel printing with flame retardant requirements. The Pc board is flame retardant, and the condenser does not self ignite, with self extinguishing properties. According to the EU ROHS directive and strict UL safety standards, UL94 has a fire rating of V0, V2, and HB. PC solar panels have good fire resistance. When the flame burns fiercely, the printed circuit board will melt, but it will not exacerbate the extension and spread of the flame. Once the flame that directly causes combustion is removed, it will immediately condense and temporarily extinguish. When the direct heat source is removed, it will quickly condense. chaom